KIRJO TILE Paint for tile roofs

     

Water-borne, acrylate based tile roof paint for maintenance painting of concrete tiles. Finish: full-matt.

KIRJO TILE is a special paint designed for maintenance painting of old tile roofs. It is suitable for both industrially painted and throughout dyed concrete and cement roof tiles.

Tehnilised andmed

Solids

About 37 % by volume

Volatile organic compound (VOC)

EU VOC limit value (kat A/i): 140 g/l. The product's VOC: max. 140 g/l.

Practical spreading rate

4 - 7 m²/l applied once with brush, depending on the absorbency and profile of the tile surface.

Density

abt. 1.25 g/ml

Drying time +23°C, the relative air humidity 50%

- dust free

- overcoatable

after 1 hour

after 8 hours

The drying will be slowed down if the air is cool and/or humid.

Thinner, clean up

Water. Wash the equipment immediately after use with appropriate detergent and warm water.

Finish

Full-matt

Colours

T2503 Dark grey, T2510 Brick red, T2513 Brown, T2515 Black

Weather resistance

The weather resistance of KIRJO TILE is good. The colour retains unchanged for a long time.

Packages (availability varies by country)

10 L

SAFETY MARKINGS

See Safety Data Sheet.

Kasutusjuhendid

Surface preparation

In order to achieve successful results, the surface to be painted must be completely cleaned from dirt, flaking and poorly adherent old paint or coating as well as brittle top layer of the concrete.

Remove loose dirt, moss and other growth from tile roof by brushing.

Clean the brushed roof using RENSA ROOF roof wash. Wet the tile surface before applying the detergent. Apply the detergent (e.g. using a low-pressure spray) and brush strongly. Rinse with clean water using a high pressure washer. NOTE! Detergent must not dry onto the surface to be painted.

Allow the washed tile surface to dry completely before priming.

Priming

Thin KIRJO TILE 15 % by volume with water. Apply the thinned paint by brush to a dry tile surface. The paint may also be applied by airless spray, but the absorption and the adhesion of the thinned paint will be enhanced if brushed immediately after the spraying.

Application

Before use stir the paint thoroughly. Top coat is not thinned.

Reserve a sufficient amount of paint in the same vessel for each uniform surface. Colour differences will thus be avoided.

Apply the paint by brush, so called roof brush or airless spray.

Recommended nozzle for airless spray is 0.015 - 0.019".

Conditions

The surface to be painted must be dry. During the application and drying period (note also the temperature of the night following the painting) the temperature of the ambient air, the surface and the paint shall be above +10 °C and the relative air humidity below 80 %.

Taking into use and maintenance

The painted surface withstands rain in normal conditions after abt. three hours drying.

The final forming of the paint film takes 3 - 4 weeks under normal circumstances and after that the ultimate durability and hardness is reached. Before this the painted surface must be treated with care.

The painted surface can be cleaned with water and a neutral (pH 6 - 8) detergent, if needed. For very dirty surfaces can also alkalescent (pH 8 - 10) detergents be used. Follow the dilution and other instructions of the detergent producer when using detergents.

Roof painted with KIRJO TILE can in the future be further maintenance painted with KIRJO TILE tile roof paint according to the instructions.

Storage

Must not freeze.

Tootekirjeldustes esitatud andmed põhinevad laboratoorsetel katsetel ja toodete praktilisel kasutamisel. Kõik esitatud väärtused on suunavad ning olenevad muu hulgas toonist ja läikeastmest. Kuna me ei saa mõjutada värvi kasutus- või tööolusid, vastutame ainult värvi kvaliteedi eest ning tagame, et see vastab Teknose kvaliteedikinnitusele. Me ei vasta kahjude eest, mis tulenevad toote kasutamisest kasutusjuhendi või -otstarbe vastaselt. Meie koduleheküljelt www.teknos.com leiab ajakohased versioonid tootekirjeldustest, ohutusjuhenditest ja süsteemikirjeldustest.